Autonerdz Home Autonerdz FAQ User’s Comments Autonerdz Events Autonerdz Store Contact Autonerdz

Autonerdz forums

 
 
 
  
  Welcome, Guest. Please Login or Register
 Autonerdz - Since 2000, North America's Authority on PicoScope
 
 
  HomeHelpSearch Member Map Event CalendarRegisterLogin  
 
  The Autonerdz Community Forums › General Public Area › PicoScope › what settings is recommended for snapon 500psi tra
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1
what settings is recommended for snapon 500psi tra (Read 3,547 times)
jobs69
Junior Member
Picogroup
**
Offline



Posts: 73

Garland tx, Texas, USA
Garland tx
Texas
USA
Gender: male
what settings is recommended for snapon 500psi tra
May 22nd, 2013 at 5:32am  
I am trying to see if anyone out there using snapon transbucers on picoscopes could recemoned some probe settings for good known captures
Back to top
 
 
IP Logged
 
Tom Roberts
Autonerdz Administrator
Picogroup
*****
Offline


Autonerdz Founder

Posts: 8,595

Olympia, Washington, USA
Olympia
Washington
USA
Gender: male
Re: what settings is recommended for snapon 500psi tra
Reply #1 - May 22nd, 2013 at 8:48am  

If you can get the specs for it then you can make a custom probe for it.  We played with one here but don't seem to have the probe we made for it anymore.

If you intend to do running compression tests with it, the pressure values won't mean much anyway.  That transducer has the same problems as so many others out there.  It's not accurate under dynamic conditions and will read impossible pressure values even with a proper probe.

It does make a nice waveform shape though....
Back to top
 
Tom Roberts
Forums Administrator
 
IP Logged
 
jarvissamuel
Super Nerd
Picogroup
*****
Offline


I love YaBB 1G - SP1!

Posts: 1,154

Denver Colorado, Colorado, USA
Denver Colorado
Colorado
USA
Re: what settings is recommended for snapon 500psi tra
Reply #2 - May 22nd, 2013 at 8:49am  
Are you powering the sensor itself or using the adapter for the Verdict to connect the transducer to the Pico?

I have a WPS so most of the time I use that but I do use my 0-100PSI Snap On transducer some for fuel pressure.  The scale I use for it is the 5 volt range. I dont know what the exact scaling is.

How the transducer is powered could change it but using the Verdict adapter .5 volts is the zero.  Above .5 is positve pressure and less than .5 volts is vacuum at least on the 100PSI one.

Sam
Back to top
 
 
IP Logged
 
crackerclicker
Super Nerd
Picogroup
*****
Offline


Elevation 834 ft

Posts: 2,358

Watertown, Wisconsin, USA
Watertown
Wisconsin
USA
Gender: male
Re: what settings is recommended for snapon 500psi tra
Reply #3 - May 22nd, 2013 at 6:09pm  
The first reply to this thread contains some rough volts to pressure conversions from Doug Montgomery. 

Have fun!   Tongue

http://productforum.autorepairdata.com/forum/showthread.php?t=656
Back to top
 
crackerclicker  
IP Logged
 
Page Index Toggle Pages: 1
‹ Previous Topic | Next Topic ›
  « Home ‹ Board Top of this page

The Autonerdz Community Forums » Powered by YaBB 2.5 AE!
YaBB Forum Software © 2000-2010. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge